Document	mce_p1p51fe30-001Q
Descrizion	Electric connections manual for application P1P51FE30-001
Drawn up	Michele Sandri
Approved	Gabriele Bazzi
Link	https://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/j1p51/p1p51fe30-001/mce_p1p51fe30-001
Language	English
Document Release	Description	Notes	Date
01	New manual		10/06/2015

<wrap lo> All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation. QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information in this document can be changed without notice. QEM shall not be held liable for any error or omission in this document. QEM® is a registered trademark.

• NO = Normally Opened
• NC = Normally Closed
• PR = Programmable
• I = Impulsive
• C = Continuous

NAME	DESCRIPTION	LOGIC			TERMINAL		HARDWARE
I01	Jog button forward Z [P]	NO	I			CN11.1	J1-P51
∩	Connect to terminal CN11.3					CN11.2
0V	Common for digital inputs					CN11.3
I1	FC Y maximum	NC	C			CN11.4
I2	FC Y minimum	NC	C			CN11.5
I3	Motor driver disk fault	NC	C			CN11.6
I4	Disc motor running	NO	C			CN11.7
I5	Disc motor in stop	NO	C			CN11.8
I6	Auxiliary OK	NO	C			CN11.9
I7	Air disc motor and thermal OK	NO	C			CN11.10
I8	Thermal engine oil pump OK	NO	C			CN11.11
0V	Common for digital inputs					CN11.12
I02	Jog button back Z [P]	NO	I			CN12.1	J1-P51
∩	Connect to terminal CN12.3					CN12.2
0V	Common for digital inputs					CN12.3
I9	Barrier closed	NO	C			CN12.4
I10	Pressure water present	NO	C			CN12.5
I11	Desk horizontal position sensor	NO	C			CN12.6
I12	Motor Driver X fault	NO	C			CN12.7
I13	Motor Driver Y fault	NO	C			CN12.8
I14	Motor Driver V fault	NO	C			CN12.9
I15	Motor Driver Z fault	NO	C			CN12.10
I16	Motor Driver C fault	NO	C			CN12.11
0V	Common for digital inputs					CN12.12
I03	Button climb tilting bench [P]	NO	I			CN13.1	J1-P51
∩	Connect to terminal CN13.3					CN13.2
0V	Common for digital inputs					CN13.3
I17	FC X maximum	NC	C			CN13.4
I18	FC X minimum	NC	C			CN13.5
I19	FC Z Up	NC	C			CN13.6
I20	FC Z Down	NC	C			CN13.7
I21	FC C maximum	NC	C			CN13.8
I22	FC C minimum	NC	C			CN13.9
I23	Low oil level	NO	C			CN13.10
I24	Micro Homing V axis	NO	C			CN13.11
0V	Common for digital inputs					CN13.12
I04	Button-down tilting bench [P]	NO	I			CN14.1	J1-P51
∩	Connect to terminal CN14.3					CN14.2
0V	Common for digital inputs					CN14.3
I25	RESET button automatic cycle [P]	NO	I			CN14.4
I26	STOP automatic cycle (HOLD) [P]	NC	I			CN14.5
I27	Jog button forward X [P]	NC	I			CN14.6
I28	Jog button back X [P]	NC	I			CN14.7
I29	Jog button forward Y [P]	NC	I			CN14.8
I30	Button jog back Y [P]	NC	I			CN14.9
I31	Selector blade speed	NC	C			CN14.10
I32	Selector spindle speed	NC	C			CN14.11
0V	Common for digital inputs					CN14.12

NAME	DESCRIPTION	TERMINAL		HARDWARE
-	Not used		CN22.1A	J1-P51
PHA1	Start button [P]		CN22.2A
PHB1	Reserve		CN22.3A
Z1	Reserve		CN22.4A
∩	Connect to terminal 5B		CN22.5A
∩	Connect to terminal 6B		CN22.6A
0V ∩	Common for count inputs Connect to terminal 7B		CN22.7A
-	Not used		CN22.1B
-			CN22.2B
-			CN22.3B
-			CN22.4B
∩	Connect to terminal 5A		CN22.5B
∩	Connect to terminal 6A		CN22.6B
∩	Connect to terminal 7A		CN22.7B

• I = Impulsive
• C = Continuous

NAME	DESCRIPTION	LOGIC		TERMINAL		HARDWARE
O01	Enabling spindle	C			CN7.2	J1-P51
O02	Activation by-pass safety barriers	C			CN7.3
O03	Turning oil pump for tilting bench	C			CN7.5
O04	Enabling EV water cooling	C			CN7.6
O05	Laser activation	C			CN7.8
O06	Machine OK	C			CN7.9
O07	Lamp presence alarm	I/C			CN7.10
O08	Enabling EV climb bench	C			CN7.11
O09	Enabling EV descent bench	C			CN8.2
O10	Enable drive axis X	C			CN8.3
O11	Enable drive axis Y	C			CN8.5
O12	Enable drive axis V	C			CN8.6
O13	Enable drive axis Z	C			CN8.8
O14	Enable drive axis C	C			CN8.9
O15	Signaling axis in motion	C			CN8.10
O16	Reset driver	I/C			CN8.11
O17	Selection rotating disk (OFF) or cutter (ON)	I/C			CN9.2
O18	Activation lubrication	C			CN9.3
O19	Lamp automatic cycle stopped [P]	C			CN9.5
O20	Lamp disk in motion with cycle stop [P]	I			CN9.6
O21	Lamp automatic cycle in progress [P]	C			CN9.8
O22	Bypass safety barriers Active lamp [P]	C			CN9.9
O23	Lamp (or beep) alarm in progress [P]	I			CN9.10
O24	Auxiliary lamp lit and ready CN [P]	C			CN9.11
O25	reserve				CN10.2
O26	reserve				CN10.3
O27	reserve				CN10.5
O28	reserve				CN10.6
O29	reserve				CN10.8
O30	reserve				CN10.9
O31	reserve				CN10.10
O32	reserve				CN10.11